How to Disinfect your Well

WELL DISINFECTION PROCEDURE: – Plan on it taking 24 to 48 hours for this procedure.
1)Thoroughly mix about 2 quarts of unscented chlorine
bleach with about 4.5 gallons of clean water. Use1 gallon of
bleach for wells over 100 feet deep.
2) Remove the well cap or sanitary seal and pour
the bleach solution directly into the well.
3) Connect a water hose to the closest  facet and run water through it until there is a strong odor of bleach.
4) Using the hose , flush the inside of the well casing or the interior walls of a dug well. Wash the well cap clean. Close the well cap, wait about  1 to 2 hours prior to continuing  to Step 5.
5)Run water through each faucet inside and outside the home until there is an odor of bleach. As soon as you smell
the  bleach from a tap, turn it off and go to the next one. If you cannot smell bleach, repeat steps 1 through 4.
6)Let the water stand in the pipes for 8 to 10 hours hours or
more best would be  overnight.
7)Flush the bleach from the well. Remember chlorine is toxic to plants and grass, so try to drain it away from your lawn or septic system.  Flush the system until you can no longer smell the bleach. This usually takes up to 4 hours. If your well might be pumped dry by doing this, then you should pump in stages. For example, pump for 30 to 60 minutes, wait for the well to recharge, and repeat.
8)Open all other indoor and outdoor faucets and run until they are clear of bleach (until odor is gone).
Note: adding
bleach to your water creates hypochlorous acid, which may dissolve rust and other sediments in the pipes. Do not be
alarmed if the water is discolored and has sediment. This will usually disappear in a few days.
9) When there is no longer any bleach odor in your water Contact  Annruelhomeinspections.com to come out to take another sample to present to the Lab

Definitions and Scope of a Home Inspection

1.1.  A general home inspection is a non-invasive, visual examination of the accessible areas of a residential property (as delineated below), performed for a fee, which is designed to identify defects within specific systems and components defined by these Standards that are both observed and deemed material by the inspector.  The scope of work may be modified by the Client and Inspector prior to the inspection process.

  1.                                                        I.            The general home inspection is based on the observations made on the date of the inspection, and not a prediction of future conditions.
  2.                                                     II.            The general home inspection will not reveal every issue that exists or ever could exist, but only those material defects observed on the date of the inspection.

1.2.  A material defect is a specific issue with a system or component of a residential property that may have a significant, adverse impact on the value of the property, or that poses an unreasonable risk to people.  The fact that a system or component is near, at or beyond the end of its normal useful life is not, in itself, a material defect.

1.3.  A general home inspection report shall identify, in written format, defects within specific systems and components defined by these Standards that are both observed and deemed material by the inspector.  Inspection reports may include additional comments and recommendations.

 

2. Limitations, Exceptions & Exclusions

2.1. Limitations:

  1.                                                        I.            An inspection is not technically exhaustive.
  2.                                                     II.            An inspection will not identify concealed or latent defects.
  3.                                                  III.            An inspection will not deal with aesthetic concerns or what could be deemed matters of taste, cosmetic defects, etc.
  4.                                                  IV.            An inspection will not determine the suitability of the property for any use.
  5.                                                     V.            An inspection does not determine the market value of the property or its marketability.
  6.                                                  VI.            An inspection does not determine the insurability of the property.
  7.                                               VII.            An inspection does not determine the advisability or inadvisability of the purchase of the inspected property.
  8.                                            VIII.            An inspection does not determine the life expectancy of the property or any components or systems therein.
  9.                                                  IX.            An inspection does not include items not permanently installed.
  10.                                                     X.            These Standards of Practice apply only to properties with four or fewer residential units.

2.2. Exclusions:

I. The inspector is not required to determine:

  1. property boundary lines or encroachments.
  2. the condition of any component or system that is not readily accessible.
  3. the service life expectancy of any component or system.
  4. the size, capacity, BTU, performance or efficiency of any component or system.
  5. the cause or reason of any condition.
  6. the cause for the need of correction, repair or replacement of any system or component.
  7. future conditions.
  8. compliance with codes or regulations.
  9. the presence of evidence of rodents, birds, animals, insects, or other pests.
  10. the presence of mold, mildew or fungus.
  11. the presence of airborne hazards, including radon.
  12. the air quality.
  13. the existence of environmental hazards, including lead paint, asbestos or toxic drywall.
  14. the existence of electromagnetic fields.
  15. any hazardous waste conditions.
  16. any manufacturers’ recalls or conformance with manufacturer installation, or any information included for consumer protection purposes.
  17. acoustical properties.
  18. correction, replacement or repair cost estimates.
  19. estimates of the cost to operate any given system.

II. The inspector is not required to operate:

  1. any system that is shut down.
  2. any system that does not function properly.
  3. or evaluate low-voltage electrical systems such as, but not limited to:

    1. phone lines;
    2. cable lines;
    3. satellite dishes;
    4. antennae;
    5. lights; or
    6. remote controls.

  4. any system that does not turn on with the use of normal operating controls.
  5. any shut-off valves or manual stop valves.
  6. any electrical disconnect or over-current protection devices.
  7. any alarm systems.
  8. moisture meters, gas detectors or similar equipment.

III. The inspector is not required to:

  1. move any personal items or other obstructions, such as, but not limited to:  throw rugs, carpeting, wall coverings, furniture, ceiling tiles, window coverings, equipment, plants, ice, debris, snow, water, dirt, pets, or anything else that might restrict the visual inspection.
  2. dismantle, open or uncover any system or component.
  3. enter or access any area that may, in the opinion of the inspector, be unsafe.
  4. enter crawlspaces or other areas that may be unsafe or not readily accessible.
  5. inspect underground items, such as, but not limited to: lawn-irrigation systems, underground storage tanks or other indications of their presence, whether abandoned or actively used.
  6. do anything which may, in the inspector’s opinion, be unsafe or dangerous to the inspector or others, or damage property, such as, but not limited to:  walking on roof surfaces, climbing ladders, entering attic spaces, or negotiating with pets.
  7. inspect decorative items.
  8. inspect common elements or areas in multi-unit housing.
  9. inspect intercoms, speaker systems or security systems.
  10. offer guarantees or warranties.
  11. offer or perform any engineering services.
  12. offer or perform any trade or professional service other than general home inspection.
  13. research the history of the property, or report on its potential for alteration, modification, extendibility or suitability for a specific or proposed use for occupancy.
  14. determine the age of construction or installation of any system, structure or component of a building, or differentiate between original construction and subsequent additions, improvements, renovations or replacements.
  15. determine the insurability of a property.
  16. perform or offer Phase 1 or environmental audits.
  17. inspect any system or component that is not included in these Standards.
  18. (From the Internachi Home Inspectors Scope of Inspections)